my keyless remote broke and iv been looking at the ebay remotes . question would be are the remotes the same matriel or are they the cheap plastic that will break if you drop your keys ? and Another question would be i have a GT but im not sure if you hit the car with a ball or something the alarm will go off does my car not have that feature or is it just not programed or something ?

If the remote still works you can replace the case: gm key fob parts
Or get one of these: key fob cover

http://www.ebay.ca/itm/REMOTE-KEYLESS-E ... 3a6efb33e0 ................. does this seem legit i just need something that wont break like those cheap plastics because i got some for my other car and i dropped it once and it went in peices

Looks good to me, Delphi is a supplier to GM but if you're concerned about damage there's a cover for that style as well: http://www.ebay.ca/itm/Pontiac-Montana- ... 414ce77454
I bought a black cover for my remote from them; it's great for reattaching your keys to a broken case, or if you happen to drop your keys a lot..

If your remote has the battery holder clip in the case, you'll need to swap it over to the new case.

thanks man will buy it soon

When i bought the car i only had one , suppose i buy the same remote that looks exactly the same can i reprogram it to work with my car ? i just got 2 today

-- Thu Jan 26, 2012 5:48 pm --

One more question , i was wondering if anyone has tightened the lower body "kit" peice on the doors ? or the panels or w.e they are called on the outside rear driver side is lose ?

You can program up to four remotes at one time, provided they are the correct ones for the car. Just make sure the part numbers and FCC ID numbers match the original one.

Here's how to program them:

Transmitter Programming

Important: All transmitters which are to be recognized by the remote control door lock transmitter (RCDLR) must be programmed in a single programming sequence. If the system is placed in program mode it will erase all previously programmed transmitters upon the receipt of the programming signal from the first transmitter. Up to four transmitters can be programmed. Do not operate or program the transmitters in the vicinity of other vehicles that are in the keyless entry program mode. This prevents the programming of the transmitters to the incorrect vehicle.

Remove the ignition key from the ignition lock cylinder.
Close all of the doors.
Remove the MALL PGM fuse from the fuse block.
Insert the ignition key into the ignition lock cylinder.
Turn the ignition to ACC.

The body control module (BCM) will perform the following in order to identify the type of BCM installed in the vehicle:
• Flash the seat belt indicator 1, 2, or 3 times.
• Chime 1, 2, or 3 times.
Turn the ignition to OFF, and then back to ACC within 1 second.

The BCM may begin to chime and flash diagnostic trouble codes (DTCs). If the BCM has stored any DTCs, refer to Diagnostic System Check - Body Control System in Body Control System.
Open and then close any vehicle door.

The BCM will chime in order to confirm that the programming mode has been entered.
Press and hold the transmitter LOCK and UNLOCK buttons simultaneously for approximately 14 seconds.

Important: After approximately 7 seconds the BCM will chime once to confirm that synchronization has been completed. After approximately 14 seconds the BCM will chime a second time to confirm that the programming has been completed.
Repeat the previous step in order to program each additional transmitter.
Remove the ignition key from the ignition lock cylinder.
Install the MALL PGM fuse into the fuse block.
Operate the functions of each transmitter in order to verify correct system operation.

thank you so much man ! ,.. i got 2 new ones, for one i just switched the transmitter shells and now the other new one is gunna need reprogramming ! ... do you know how to tighten the lower body panel under the door ? not the rockers just above it ? one side seems kinda lose

From what I've read, those are held on with adhesive and a support piece that's pinned to the door. Check out Document ID: 572275 Door Lower Finish Panel Replacement in the GM Service Manual for more info.

alri kool thanks again !

i tried that todai and it didnt work -_- what can it be ? i only heard the chimes after i opened the door :S ? kinda confused

Print out or write down the instructions (if you didn't already do it), and try programming them again. Maybe you just missed a step or did something out of sequence.

lol it was acutually the battery that was out my bad lol thanks for the help though !